탄소합금후판 (Carbon and Alloy Steel Cut-to-length Plate)

사건 정보

설명

The products covered by this investigation are certain carbon and alloy steel hotrolled or forged flat plate products not in coils, whether or not painted, varnished, or coated with plastics or other non-metallic substances (cut-to-length plate). Subject merchandise includes plate that is produced by being cut-to-length from coils or from other discrete length plate and plate that is rolled or forged into a discrete length. The products covered include (1) Universal mill plates (i.e., flatrolled products rolled on four faces or in a closed box pass, of a width exceeding 150 mm but not exceeding 1250 mm, and of a thickness of not less than 4 mm, which are not in coils and without patterns in relief), and (2) hot-rolled or forged flat steel products of a thickness of 4.75 mm or more and of a width which exceeds 150 mm and measures at least twice the thickness, and which are not in coils, whether or not with patterns in relief. The covered products described above may be rectangular, square, circular or other shapes and include products of either rectangular or non-rectangular cross-section where such non-rectangular cross-section is achieved subsequent to the rolling process, i.e., products which have been “worked after rolling” (e.g., products which have been beveled or rounded at the edges). For purposes of the width and thickness requirements referenced above, the following rules apply: (1) except where otherwise stated where the nominal and actual thickness or width measurements vary, a product from a given subject country is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above unless the product is already covered by an order existing on that specific country (i.e., Certain Hot Rolled Steel Flat Products from Australia, Brazil, Japan, the Republic of Korea, the Netherlands, the Republic of Turkey, and the United Kingdom: Amended Final Affirmative Antidumping Determination for Australia, the Republic of Korea, and the the Republic of Turkey and Antidumping Duty Orders, 81 FR 67962 (October 3, 2016), and (2) where the width and thickness vary for a specific product (e.g., the thickness of certain products with non-rectangular cross-section, the width of certain products with non-rectangular shape, etc.), the measurement at its greatest width or thickness applies. Steel products included in the scope of this investigation are products in which: (1) iron predominates, by weight, over each of the other contained elements; and (2) the carbon content is 2 percent or less by weight. Subject merchandise includes cut-to-length plate that has been further processed in the subject country or a third country, including but not limited to pickling, oiling, levelling, annealing, tempering, temper rolling, skin passing, painting, varnishing, trimming, cutting, punching, beveling, and/or slitting, or any other processing that would not otherwise remove the merchandise from the scope of the investigation if performed in the country of manufacture of the cut-to-length plate. All products that meet the written physical description, are within the scope of this investigation unless specifically excluded or covered by the scope of an existing order. The following products are outside of, and/or specifically excluded from, the scope of this investigation: (1) products clad, plated, or coated with metal, whether or not painted, varnished or coated with plastic or other non-metallic substances; (2) military grade armor plate certified to one of the following specifications or to a specification that references and incorporates one of the following specifications: · MIL-A-12560, · MIL-DTL-12560H, · MIL-DTL-12560J, · MIL-DTL-12560K, · MIL-DTL-32332, · MIL-A-46100D, · MIL-DTL-46100-E, · MIL-46177C, · MIL-S-16216K Grade HY80, · MIL-S-16216K Grade HY100, · MIL-S-24645A HSLA-80; · MIL-S-24645A HSLA-100, · T9074-BD-GIB-010/0300 Grade HY80, · T9074-BD-GIB-010/0300 Grade HY100, · T9074-BD-GIB-010/0300 Grade HSLA80, · T9074-BD-GIB-010/0300 Grade HSLA100, and · T9074-BD-GIB-010/0300 Mod. Grade HSLA115, except that any cut-to-length plate certified to one of the above specifications, or to a military grade armor specification that references and incorporates one of the above specifications, will not be excluded from the scope if it is also dual- or multiple-certified to any other non-armor specification that otherwise would fall within the scope of this order; (3) stainless steel plate, containing 10.5 percent or more of chromium by weight and not more than 1.2 percent of carbon by weight; (4) CTL plate meeting the requirements of ASTM A-829, Grade E 4340 that are over 305 mm in actual thickness; (5) Alloy forged and rolled CTL plate greater than or equal to 152.4mm in actual thickness meeting each of the following requirements: (a) Electric furnace melted, ladle refined & vacuum degassed and having a chemical composition (expressed in weight percentages): · Carbon 0.23-0.28, · Silicon 0.05-0.20, · Manganese 1.20-1.60, · Nickel not greater than 1.0, · Sulfur not greater than 0.007, · Phosphorus not greater than 0.020, · Chromium 1.0-2.5, · Molybdenum 0.35-0.80, · Boron 0.002-0.004, · Oxygen not greater than 20 ppm, · Hydrogen not greater than 2 ppm, and · Nitrogen not greater than 60 ppm; (b) With a Brinell hardness measured in all parts of the product including mid thickness falling within one of the following ranges: (i) 270-300 HBW, (ii) 290-320 HBW, or (iii) 320-350HBW; (c) Having cleanliness in accordance with ASTM E45 method A (Thin and Heavy): A not exceeding 1.5, B not exceeding 1.0, C not exceeding 0.5, D not exceeding 1.5; and (d) Conforming to ASTM A578-S9 ultrasonic testing requirements with acceptance criteria 2 mm flat bottom hole; (6) Alloy forged and rolled steel CTL plate over 407 mm in actual thickness and meeting the following requirements: (a) Made from Electric Arc Furnace melted, Ladle refined & vacuum degassed, alloy steel with the following chemical composition (expressed in weight percentages): · Carbon 0.23-0.28, · Silicon 0.05-0.15, · Manganese 1.20-1.50, · Nickel not greater than 0.4, · Sulfur not greater than 0.010, · Phosphorus not greater than 0.020, · Chromium 1.20-1.50, · Molybdenum 0.35-0.55, · Boron 0.002-0.004, · Oxygen not greater than 20 ppm, · Hydrogen not greater than 2 ppm, and · Nitrogen not greater than 60 ppm; (b) Having cleanliness in accordance with ASTM E45 method A (Thin and Heavy): A not exceeding 1.5, B not exceeding 1.5, C not exceeding 1.0, D not exceeding 1.5; (c) Having the following mechanical properties: (i) With a Brinell hardness not more than 237 HBW measured in all parts of the product including mid thickness; and having a Yield Strength of 75ksi min and UTS 95ksi or more, Elongation of 18% or more and Reduction of area 35% or more; having charpy V at - 75 degrees F in the longitudinal direction equal or greater than 15 ft. lbs (single value) and equal or greater than 20 ft. lbs (average of 3 specimens) and conforming to the requirements of NACE MR01-75; or (ii) With a Brinell hardness not less than 240 HBW measured in all parts of the product including mid thickness; and having a Yield Strength of 90 ksi min and UTS 110 ksi or more, Elongation of 15% or more and Reduction of area 30% or more; having charpy V at - 40 degrees F in the longitudinal direction equal or greater than 21 ft. lbs (single value) and equal or greater than 31 ft. lbs (average of 3 specimens); (d) Conforming to ASTM A578-S9 ultrasonic testing requirements with acceptance criteria 3.2 mm flat bottom hole; and (e) Conforming to magnetic particle inspection in accordance with AMS 2301; (7) Alloy forged and rolled steel CTL plate over 407 mm in actual thickness and meeting the following requirements: (a) Made from Electric Arc Furnace melted, ladle refined & vacuum degassed, alloy steel with the following chemical composition (expressed in weight percentages): · Carbon 0.25-0.30, · Silicon not greater than 0.25, · Manganese not greater than 0.50, · Nickel 3.0-3.5, · Sulfur not greater than 0.010, · Phosphorus not greater than 0.020, · Chromium 1.0-1.5, · Molybdenum 0.6-0.9, · Vanadium 0.08 to 0.12 · Boron 0.002-0.004, · Oxygen not greater than 20 ppm, · Hydrogen not greater than 2 ppm, and · Nitrogen not greater than 60 ppm. (b) Having cleanliness in accordance with ASTM E45 method A (Thin and Heavy): A not exceeding 1.0(t) and 0.5(h), B not exceeding 1.5(t) and 1.0(h), C not exceeding 1.0(t) and 0.5(h), and D not exceeding 1.5(t) and 1.0(h); (c) Having the following mechanical properties: A Brinell hardness not less than 350 HBW measured in all parts of the product including mid thickness; and having a Yield Strength of 145ksi or more and UTS 160ksi or more, Elongation of 15% or more and Reduction of area 35% or more; having charpy V at - 40 degrees F in the transverse direction equal or greater than 20 ft. lbs (single value) and equal or greater than 25 ft. lbs (average of 3 specimens); (d) Conforming to ASTM A578-S9 ultrasonic testing requirements with acceptance criteria 3.2 mm flat bottom hole; and (e) Conforming to magnetic particle inspection in accordance with AMS 2301. At the time of the filing of the petition, there was an existing antidumping duty order on certain cut-to-length carbon-quality steel plate products from Korea.(See Notice of Final Determination of Sales at Less Than Fair Value: Certain Cut-To-Length Carbon-Quality Steel Plate Products from Korea, 64 Fed. Reg. 73,196(Dep’t Commerce Dec. 29, 1999), as amended, 65 Fed. Reg. 6,585 (Dep’t Commerce Feb 10, 2000) (1999 Korea AD Order)). The scope of the antidumping duty investigation with regard to cut-to-length plate from Korea covers only (1) subject cut-to-length plate not within the physical description of cut-to-length carbon quality steel plate in the 1999 Korea AD Order, regardless of producer or exporter; and (2) cut-to-length plate produced and/or exported by those companies that were excluded or revoked from the 1999 Korea AD Order as of April 8, 2016. The only revoked or excluded company is Pohang Iron and Steel Company, also known as POSCO. The products subject to the investigation are currently classified in the Harmonized Tariff Schedule of the United States (HTSUS) under item numbers: 7208.40.3030, 7208.40.3060, 7208.51.0030, 7208.51.0045, 7208.51.0060, 7208.52.0000, 7211.13.0000, 7211.14.0030, 7211.14.0045, 7225.40.1110, 7225.40.1180, 7225.40.3005, 7225.40.3050, 7226.20.0000, and 7226.91.5000. The products subject to the investigation may also enter under the following HTSUS item numbers: 7208.40.6060, 7208.53.0000, 7208.90.0000, 7210.70.3000, 7210.90.9000, 7211.19.1500, 7211.19.2000, 7211.19.4500, 7211.19.6000, 7211.19.7590, 7211.90.0000, 7212.40.1000, 7212.40.5000, 7212.50.0000, 7214.10.0000, 7214.30.0010, 7214.30.0080, 7214.91.0015, 7214.91.0060, 7214.91.0090, 7225.11.0000, 7225.19.0000, 7225.40.5110, 7225.40.5130, 7225.40.5160, 7225.40.7000, 7225.99.0010, 7225.99.0090, 7226.11.1000, 7226.11.9060, 7226.19.1000, 7226.19.9000, 7226.91.0500, 7226.91.1530, 7226.91.1560, 7226.91.2530, 7226.91.2560, 7226.91.7000, 7226.91.8000, and 7226.99.0180. The HTSUS subheadings above are provided for convenience and customs purposes only. The written description of the scope of the investigation is dispositive.

출처: 한국무역협회 수입규제 통합조회 · 원문 보기 ↗

경과 23건

1. 2026-08-06
   재심 · 예비판정

   업체명 POSCO 마진 0.60 비고 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 8차 연례재심 예비판정 - 심사대상기간(POR): 2024. 5. 1. ~ 2025. 4. 30.

2. 2026-04-16
   재심 · 최종판정

   업체명 POSCO 마진 0.00 비고 미소마진 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 7차 연례재심 최종판정 - 심사대상기간(POR): 2023. 5. 1. ~ 2024. 4. 30.

3. 2025-09-11
   재심 · 예비판정

   업체명 POSCO 마진 0.00 비고 미소마진 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 7차 연례재심 예비판정 - 심사대상기간(POR): 2023. 5. 1. ~ 2024. 4. 30.

4. 2025-02-21
   재심 · 최종판정

   업체명 POSCO 마진 0.00 비고 미소마진 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 6차 연례재심 최종판정 - 심사대상기간(POR): 2022. 5. 1. ~ 2023. 4. 30.

5. 2024-06-06
   재심 · 예비판정

   업체명 POSCO 마진 0.00 비고 미소마진 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 6차 연례재심 예비판정 - 심사대상기간(POR): 2022. 5. 1. ~ 2023. 4. 30.

6. 2023-12-14
   재심 · 최종판정

   업체명 POSCO 마진 0.00 비고 미소마진 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 5차 연례재심 최종판정 - 심사대상기간(POR): 2021. 5. 1. ~ 2022. 4. 30.

7. 2023-06-21
   재심 · 예비판정

   업체명 POSCO 마진 0.00 비고 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 5차 연례재심 예비판정 - 심사대상기간(POR): 2021. 5. 1. ~ 2022. 4. 30.

8. 2022-10-12
   재심 · 최종판정

   업체명 POSCO 마진 2.59 비고 업체명 기타(All-Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 4차 연례재심 최종판정 - 심사대상기간(POR): 2020. 5. 1. ~ 2021. 4. 30.

9. 2022-06-01
   재심 · 예비판정

   업체명 POSCO 마진 2.80 비고 업체명 기타(All Others) 마진 7.10 비고 현금예치율(Cash Deposit) * DOC, 4차 연례재심 예비판정 - 심사대상기간(POR): 2020. 5. 1. ~ 2021. 4. 30.

10. 2022-03-25
    일몰재심 · 최종판정

    * DOC, 일몰재심 최종 긍정판정(반덤핑 유지) # 일몰재심

11. 2022-02-04
    재심 · 최종판정

    업체명 포스코 마진 0.00 비고 미소마진 업체명 기타(All Others) 마진 7.10 비고 현금예치금(Cash Deposit) * DOC 3차 연례재심 최종판정 - POR : 2019. 5. 1. ~ 2020. 4. 30. # 미소마진

12. 2021-08-06
    재심 · 예비판정

    업체명 포스코 마진 0.00 비고 미소마진 업체명 기타(All Others) 마진 7.10 비고 현금예치금(Cash Deposit) * DOC 3차 연례재심 예비판정 - POR : 2019. 5. 1. ~ 2020. 4. 30. # 미소마진

13. 2021-03-24
    재심 · 최종판정

    업체명 포스코 마진 0.00 비고 업체명 기타(All Others) 마진 7.10 비고 현금예치금(Cash Deposit) * DOC 2차 연례재심 최종판정 - POR : 2018. 5. 1. ~ 2019. 4. 30.

14. 2020-07-20
    재심 · 예비판정

    업체명 포스코 마진 0.00 비고 업체명 Non-examined 마진 0.00 비고 업체명 기타(All Others) 마진 7.39 비고 현금예치금(Cash Deposit) * DOC 2차 연례재심 예비판정 - POR : 2018. 5. 1. ~ 2019. 4. 30. * Non-examined 기업 리스트 : Buma Ce Co Ltd., Dong Yang Steel Pipe Co Ltd., Dongkuk Steel Mill Co Ltd., Expeditors Korea Ltd., Haem Co Ltd., Hyundai Clovis Co Ltd., Hyundai Steel Company, J.I. Sea & Air Express Co Ltd., Maxpeed Co Ltd., Ramses Logistics Co Ltd., and Sumitomo Corp Korea Ltd. *Non-examined 11개 기업에 대한 재심은 철회, 포스코에 대해서만 재심 진행

15. 2019-12-26
    재심 · 최종판정

    업체명 포스코 마진 19.87 비고 업체명 Non-examined 마진 19.87 비고 업체명 기타(All Others) 마진 7.10 비고 현금예치금(Cash Deposit) * DOC 1차 연례재심 최종판정 - POR : 2016. 11. 14. ~ 2018. 4. 30. * Non-examined 기업 리스트 : Buma Ce Co Ltd., Dong Yang Steel Pipe Co Ltd., Dongkuk Steel Mill Co Ltd., Expeditors Korea Ltd., Haem Co Ltd, J.I. Sea & Air Express Co Ltd., Maxpeed Co Ltd., Ramses Logistics Co Ltd., Sumitomo Corp Korea Ltd

16. 2019-07-10
    재심 · 예비판정

    업체명 포스코 마진 20.09 비고 업체명 Non-examined 마진 20.09 비고 업체명 기타(All Others) 마진 7.39 비고 현금예치금(Cash Deposit) *DOC 1차 연례재심 예비판정 - POR : 2016. 11. 14. ~ 2018. 4. 30. *Non-examined 기업 리스트 : Buma Ce Co Ltd., Dong Yang Steel Pipe Co Ltd., Dongkuk Steel Mill Co Ltd., Expeditors Korea Ltd., Haem Co Ltd., Hyundai Glovis Co Ltd., Hyundai Steel Company, J.I. Sea & Air Express Co Ltd., Maxpeed Co Ltd., Rames Logistics Co Ltd., Sumitomo Corp Korea Ltd.

17. 2017-05-25
    원심 · 부과명령

    업체명 포스코 마진 7.10 비고 업체명 기타(All Others) 마진 7.10 비고 DOC 반덤핑 관세부과 - 반덤핑 관세 수정

18. 2017-05-05
    원심 · 최종판정

    ITC 산업피해 최종 긍정판정

19. 2017-04-04
    원심 · 최종판정

    업체명 포스코 마진 7.39 비고 업체명 기타(All Others) 마진 7.39 비고 DOC 반덤핑 최종판정

20. 2016-11-14
    원심 · 예비판정

    업체명 포스코/포스코대우 마진 6.82 비고 업체명 기타(All Others) 마진 6.82 비고 DOC 반덤핑 예비판정

21. 2016-05-20
    원심 · 예비판정

    ITC 예비판정 : 산업피해 긍정

22. 2016-04-08
    제소

    ArcelorMittal USA LLC, Nucor Corporation, SSAB Enterprises, LLC 피제소국 : 한국, 오스트리아,벨기에, 브라질, 프랑스, 독일, 이탈리아, 일본, 중국, 남아공, 대만, 터키

23. 2016-04-08
    조사개시

    DOC 반덤핑 조사개시: 2016.4.28. -POI : 2015. 4. 1. ~ 2016. 3. 31.